Ce site utilise des cookies. Pour savoir plus sur le but de leur utilisation lisez notre politique de confidentialité. x
En utilisant ce site, vous acceptez l'utilisation de cookies, selon les paramètres actuels de votre navigateur.

Actualité

2019-05-14Clapets coupe feu FDA2 avec trappe de visite

Clapets coupe feu FDA2 avec trappe de visite

The FDA2-12 round fire dampers are designed for use in general ventilation systems to seal off smoke and fire between adjacent fire partitions. The fire damper blade remains open under normal operating conditions. It is closed shut automatically in the event of a fire. 

  • The fire dampers are classified according to EN 13501-3+A1:2010P,
  • The fire resistance was tested as per EN 1366-2:2015,
  • The entire manufacturing process meets the requirements of EN 15650:2010.

 BENEFITS:

  • The FDA2-12 fire dampers can be installed in horizontal and vertical fire partitions to provide fire resistance of
    EI 120 (ve ho i↔o)
     S

  • Designed for round and rectangular ventilation systems,

  • Available dimensions: in the nominal sizes from 160x160 to 1000x500mm or diameter from 200 to 630mm,
  • The dampers have an inspection panel,
  • Possible use of fire dampers in general ventilation,
  • All fire dampers have a torsion spring trip (in version FDA2-12-T) or
  • a return-spring actuator coupled with a thermal trip (in version FDA2-12-M).

The fire dampers can be installed in the following partitions: concrete separing floor, concrete wall, solid brick wall, cellular concrete unit wall, gybsum board wall on steel frame.

 

plus d'informations

2019-04-03SMOKE System - les gaines et les raccords de desenfumage

SMOKE System - les gaines et les raccords de desenfumage

The system of single-compartment steel, circular smoke extraction ducts in E600 120 (ho) S1500 single fire resistance class is intended to be used in the construction industry in a horizontal system as elements creating a smoke extraction ventilation system or combined ventilation, fulfilling at the same time the functions of general and smoke extraction ventilation, assuming that they serve only the compartment in which they have been installed. Systems serving one fire compartment may be independent systems or may be combined with a collective, multi-compartment system. The main task of the smoke extraction systems is to remove hot gases and smoke from the area covered by the fire in order to facilitate the evacuation of people and to enable the extinguishing action and the evacuation of people from the area at risk, while complying with the criteria of fire and/or smoke tightness specified under conditions of exposure to a temperature of 600°C.

 
SMOKE system single-compartment circular smoke extraction ducts have the following application areas:

  • Smoke extraction ducts are designed for single fire compartments,

  • The smoke extraction ducts are available in diameter range is from Ø100 to Ø1000mm,
  • The maximum temperature of the fire gases discharged through the SMOKE system ducts is 600 °C,
  • Individual duct sections and ventilation fittings of SMOKE system ducts may only be installed horizontally (vertical installation is not permitted),
  • The scope of application of smoke extraction ducts includes ventilation systems with operating pressure from -1500 Pa to +500 Pa.

 

 

plus d'informations

2019-03-21FLX-REKU - The complete air distribution system in a brand NEW version

FLX-REKU - The complete air distribution system in a brand NEW version

The smart solution for air distribution - FLX-REKU system: 

The FLX-REKU air distribution ductwork consists of ventilation semi-rigid ducts, distribution and plenum boxes, ventilation dampers and other elements that, together with a heat recovery unit, constitute a complete mechanical ventilation system with heat recovery (MVHR). The FLX-REKU system is a great solution when high durability and flexibility are required. The high circumferential rigidity allows burying the ducts in concrete.

 BENEFITS:

  • Aesthetics of the installation - high durability and mechanical strength allows for assembly in a concrete screed in the ceiling or in the insulation layer,
  • Small dimensions and a unique structure allow installing FLX ducts under the ceiling, on walls and laid on floors,
  • The minimum number of joints ensures minimal pressure loss,
  • The antimicrobial lining in FLXHDPE-A ducting contains silver ions,
  • Quick and easy assembly - the offer includes all necessary couplers and mounting accessories!
  • Guaranteed airtight installation - connections with EPDM gaskets,

We have expanded the range of FLX-REKU system products with silencers, offsets and UPgraded the design of plenum and distribution boxes!!

 

plus d'informations

2019-02-19Meet us at ISH 2019

Meet us at ISH 2019

We would like to invite you to visit ISH 2019 which will take place in Frankurt on 11-15 March. 2019. Let's meet at ISH 2019 at Alnor's stand no C31 in Hall 8.0.

We'll be expecting You from 11. - 14.3.2019 (Monday to Thursday): 9 a.m. to 6 p.m, and on 15.3.2019 (Friday - Public day): 9 a.m. to 5 p.m.

Don't miss opportunity for talk about our new products which can make your offer more attractive, amongst them smoke extraction system, new models of fire dampers and VAV and CAV regulators. .

plus d'informations

2019-02-19MOCarz-CA - Utilisez le côté positif du charbon

MOCarz-CA - Utilisez le côté positif du charbon

Better filtration properties: 

The new MOCarz-CA a filter box has been equipped with a brand new active carbon filter. In MOCarz-AC filter box, the initial flat filter was replaced with an activated carbon filter with the „W” design. The main purpose of such a material is deodorization of the air and preliminary cleaning of dust and gaseous pollutants. It doesn’t generate additional air flow resistance in comparison to the standard MOCarz version!

 BENEFITS:

  • Filtration and purification of the outside air from smels,
  • PM2,5 removal efficiency reaches up to 73%, and PM10 removal efficiency - up to 81%,
  • Airtight filter casing,
  • More accurate filtration properties thanks to the usage of two filters: prefilter and anti-smog filter,
  • No additional resistance to the standard MOCarz filter box! I has been observed even a few percent lower initial resistance of the clean filter!
  • The perfect solution for domestic ventilation systems with a heat recovery.

You probably already have such a filter in your car. Install it also in your home!

 

plus d'informations

2019-02-19Plus de 1000 produits dans un seal endroit!

Plus de 1000 produits dans un seal endroit!

 

Get to know our Product Range – Check our Product Overview! On 44 pages we’ve shown over 1000 products, described more than 10 ventilation systems and reviewed all our certificates, technical approvals as well as selection software that supports our clients. 

Examples of our ventilation systems:

  1. The SPIRAL-System is a proven system of quick-coupled spiral ducts and fittings provided with factory-installed EPDM gaskets. The gaskets provide leak-proof and durable joints between SPIRAL®system components. The system components are available in a full range of diameters from Ø80 to Ø1250 mm. SPIRAL system meets the requirements of PN-EN 12237 for air tightness class D (Certificate no. 0103/07).
  2. Components of the FIX-System suspension are made from galvanized steel or stainless steel and they meet the requirements of the BRI (ITB) Technical Recommendation no. RT ITB - 1112/2008 Includes: EQVS, EQZS, EQLS, CLR, CLRL, TKN, KLQ, PG, TK, LDB, PB.
  3. Roof installation accessories are a range of fixtures and tools for easy and safe suspension of round and square ventilation ducts. Roof installation accessories are a range of modular roof support kits and roof feet, as well as other accessories that make the assembly easy and fast. Sets of roof supports can be used on flat roofs and slightly sloped roof. Roof support kit consist of perfectly matched elements - roof feet, sections of channel, screws, nuts, etc.
  4. FLX-REKU is a complete ventilation system which comprises ventilation ducts, plenum boxes, air dampers and other components for building ventilation solutions with heat-recovery units. The system comes very handy when heavy-duty and flexible ducts are required. The high circumferential rigidity allows burying the ducts in concrete.
  5. The EPP duct system is made of expanded polypropylene. The system has a number of design and installation advantages: low weight, quick installation (no additional connectors or screws required), no additional insulation is required since the material itself is already an insulator, easy to cut using hand tools, no thermal bridges. Thermal conductivity: λ=0.039 [W / m * k].
  6. SQUER-System - rectangular ducts and fittings.
  7. The IZOL®system is a registered tradename of pre-insulated ventilation ducts and fittings for indoor and outdoor systems. All system components are provided with inner and outer steel sheet cladding, and a thermal-insulation layer in between. The nominal diameter range of 100-500 mm always refers to the inner diameter of ducts and fittings. There are 3 types of insulation  available: 25 / 50 / 100 mm.
  8. Ducts and fittings insulated with rubber foam Fovent®system. The insulation made of rubber mat is available in 4 sizes: 9, 13, 19 and 25 mm.
  9. Insulated fittings IZOL-SAFE System designated for marine applications. Bend with air-insulation and duct with wool based insulation.
  10. OFF-SHORE ventilation ducts and fitting - Circular ducts and fittings made of galvanized metal sheets, stainless steel 1.4404, wall thickness in stainless steel fittings from 0,8 up to 1,25 mm depending on diameterr. Swelling gasket for high temperatures purposes.
  11. Ventilation systems made of plastics are widely used in many areas and sectors where the conventional materials, such as plated steel or stainless steel become insufficient due to their limitations. Plastics have traditionally been used in laboratories, chemical industry or spaces of high purity grade.
  12. TRANS-Quick is a modern clamp-together ducting system intended for industrial dust extraction. Quick assembly and disassembly, using pull rings to connect components - which can be reused and reassembled.Ducts and fittings are manufactured from galvanised steel sheet 0.7 and 0.9 mm in thickness using butt welding method, components are joined with clamps equipped with a gasket.
  13. Circular smoke extraction ducts and fittings SMOKE-SYSTEM.

 

In our product offer You can also find:

  • Heat recovery unit
  • Filters prevent contaminants from flowing with the air supplied into rooms and ventilation ductwork.
  • Valves and ventilation grillse
  • Ventilation duct silencers
  • Ventilation dampers, vav flow regulatores and actuators
  • Duct heaters
  • Access doors 
  • Duct fans
  • Roof hoods and cowls
  • Fire dampers and valves

 

Moreover, our products are tested and certified by:

RISE - Research Institutes of Sweden AB Certification (former SITAC)
Air Tightness Certificate for Ventilation Ductwork System - air tightness class D according to EN 12237:2003 - round spiral ducts and ductwork fittings with seals.

The Building Information Foundation RTS sr
M1 Cleanliness class for air handling components:

  • Ventilation spiral ducts
  • Pressed bends, reducers, T-pieces and take-offs
  • Segmented bends, reducers, T-pieces, take-offs, male couplings, offsets
  • Air dampers: regulating, shut-off, iris, multi blade

TÜV Rheinland Polska
Certificate of production quality:

  • Round ventilation ducts and fittings
  • Mounting accessories
  • Regulating, shut-off, non-return and iris dampers
  • Ventilation silencers

Instytut Techniki Budowlanej ITB (The Building Research Institute)
Technical approvals and certificates of constancy of performance

  • STRUT assembly system
  • Suspended mounting elements
  • Flexible ducts - fire classification
  • Fire dampers

Passive House Institute
Certificate for HRU-PremAIR-450 heat recovery unit confirming compliance with the highest energy efficiency requirements.

...
and many others.

 

plus d'informations

2019-01-15Quel Premair va vous choisir? +500 +450 +350

Quel Premair va vous choisir? +500 +450 +350

Heat recovery ventilation unit HRU-PremAIR is a modern device with 350 / 450 or 500 m3/h air flow @ 100 Pa!!

Unit is made from cutting edge materials - PET or aluminim heat exchanger and EPP self-supporting casing. The device operation is controlled by an advanced PCB with wireless communication between control panels and sensors. IN addition, the
HRU-PremAIR can be connected to the Internet and controlled by an mobile application.
HRU-PremAIR-450 is certified by Passive House Institute and can be used as a certified component in passive houses.

Key performance features:
 • Heat recovery:
        HRU-PremAIR-350 - up to 92,9%
        HRU-PremAIR-450 - up to 93,4%
        HRU-PremAIR-500 - up to 82,6%
 • Certified heat exchanger from PET with high performance (Eurovent Certification) and hygienic compliance with DIN EN ISO 846 standard
 • Hi-tech modern casing made of Expanded Polypropylene - EPP
 • High mechanical resistance
 • High thermal and acoustic insulation
 • Modulated by-pass
 • Free-cooling and Free-heating functions
 • Performance tested according to EN 13141-7 standard
 • Complies with ErP2018
 • Wall mounting racks and feet included
 • Replaceable duct connections
 • Wireless control through mobile application or web browser
 • Remote control possible by any CO2 or RH wireless sensor
 • Light weight construction – only 32 kg!
 • POLISH product

plus d'informations

2019-01-02Gazelles du business 2018

Gazelles du business 2018

Le ranking Gazele Biznesu est le palmarès des petites et moyennes entreprises à croissance la plus rapide. Du point de vue de la revue « Puls Biznesu », une « Gazelle » est une entreprise de taille moyenne qui, grâce à une croissance très dynamique, peut faire face même à des concurrents beaucoup plus grands. Les classements Gazele Biznesu sont élaborés chaque année par les revues économiques faisant partie du groupe suédois  Bonnier Press Group. À part « Puls Biznesu », de telles listes sont dressées par d’autres revues en Suède, Danemark, Autriche, Lettonie, Russie, Estonie et Slovénie. Les critères de sélection des « Gazelles » diffèrent d’un pays à l’autre, en fonction des conditions économiques locales, mais l’objectif est toujours le même : promotion des petites et moyennes entreprises.

plus d'informations

2018-10-12HRU-WALL-RC - centrale de récupération avec télécommande

HRU-WALL-RC - centrale de récupération avec télécommande

NEW! Push-pull heat recovery unit with remote control:

  • Infra-red remote controller with touch technology, LCD display and wall base supplied as standard.
  • Regenerative heat exchanger with ceramic core; high thermal efficiency (up to 82%).
  • 5 speeds:  20-30-40-50-60 m3/h.
  • Automatically manages the cycle length in COMFORT mode.
  • Dirty filter visual indicator.
  • Boost function - maximum air flow for limited time – 5th speed for 15 minutes.
  • Integrated humidity sensor – smart humidity control, increases speed if rapid rise of relative humidity is measured
  • Anti-frost protection.
  • Free-cooling - only one direction.

 

plus d'informations

2018-09-04Meet us at SMM 2018

Meet us at SMM 2018

Join ALNOR team at the largest fair trade for Marine industry in Germany SMM 2018 in Hamburg between 4-7.09.2018. 

We're presenting 5 complete ventilation systems for marine applications: pre-insulated ductwork with 10, 16 and 25mm insulation, air insulate ductwork and aluminium system, as well as offshore ventilation system made of stainless steel.

You are very welcome in Hall B5, booth B5.516 to talk with us about cooperation.

plus d'informations
REKUPERACJA
PROJEKTOWANIE